|
|
Michael
January 2, 2022
Had to modify one of the screws to not impact the extractor spring assembly. Seems like trijicon could have produced this product with the correct size screws for a very small incremental cost.
|
Adam
May 6, 2023
This is not a bad review on Euro, I'm always happy with Euro. But don't waste your time or money on this configuration.
Bought the RMR adapter plate for my Sig P320 Xcarry yesterday 5/5/23 from Euro. It was actually listed as "used" which I was ok with because the "new" ones were out of stock.
I also got the sealing plate for under the RMR.
Got home and started to mount the RMR06. Supplied mounted screws were stripped out, thanks to whoever returned it to Euro, #$@%/$÷@@!!. To the hardware store and back home.
I then had to trim one of the screws that mount the adapter plate to the slide like other people have mentioned. Otherwise it will contact the spring on the extractor.
Get it all mounted up, felt great, felt natural, pointed good. Lot better quality than the POS original Gen 1 version Romeo it was replacing, unless you leave them in the safe then they're ok. Anyway...
To the range to zero. Pistol range is 15 yards, so that's what I had to work with. Well, after all that, I ran out of elevation adjustment on the RMR. Best I could do was 5 1/2" low at 15 yards and it wouldn't come up any more!
The Xcarry slide is milled for the Romeo to sit down on the slide. I assume that when you stack the adapter plate on top of the slide and the RMR on top of that, its just too much height for the RMR to adjust for. Bad design I guess. I'm surprised Trijicon put this out when it doesn't work. Maybe that's why they're out of stock?
So, as I'm writing this review and I just removed the RMR, adapter plate and reinstalled the factory rear sights...don't waste your time or money because it doesn't work.
|
Richard Rios-Beauchamp
January 7, 2022
This RMR mount fit my Sig P320 X Carry perfectly. My slide had a Romeo1 Pro installed at moment of purchase but died out after a couple of years. I installed a Trijicon RMR 3.25 MOA and the fit was easy and with absolutely no issues. Thank you for a very pleasant experience from purchase to installation.
|
TROY JOHNSON
October 13, 2021
This RMR mount fit my Sig P320 X Carry perfectly. My slide has holes drilled in it for a Romeo1 Pro only. With this mount, I was able to use the new Holosun 507C Vulcan ACSS. Very happy with my purchase from EuroOptics as always.
|
Mike
September 18, 2020
The plate is a great fit. However, the mounting screws had to be modified to properly be seated. In the 320X5 the screw above the extractor was way too long and it bent my spring. I used a pair of vise locks and am angle grinder. Made for an interesting time. But it's ground down way shorter and fit.
|
Ryan
September 8, 2020
The plate itself was below par. The notches that line up with the rmr are too large. The screws that secure the plate to the gun are too long. And comes with no hex head Alan key. But nothing a dremel can’t fix, would be nice to not have to use one in the first place but whatever
|
Alex V
September 3, 2020
Fit nicely overall. I had an issue with the length of the plate mounting screws, but i was able to file one of them down.
|
Ken
June 4, 2020
Excellent fit and finish. Didn't have to modify at all. I have the newer xcarry with rear sight dovetail. Plate fits well. Not snap in, like some aftermarket slide milling, but good enough for my needs. Excellent service from EuroOptic!
|
Max
May 27, 2020
Fit & finish as expected - worked great
|
Jeremy Reeves
April 22, 2020
This product is nearly perfect for the X-Carry. It did require some removal of material from the red dot mounting holes with a Dremel, to get a flush fit. Other than that, pretty standard mounting plate.
|